A pasture fence is a long tension system with a few hard points, not a tall privacy face. If you plan it like a backyard wood run, you will under-count braces and over-think pickets. The useful numbers on a field-fence job are the distance, the line-post spacing, the number of corners and gates, the wire type, and the roll length. Here is how to use those figures on a material list, and when a fuller takeoff is the next step.

Farm and ranch materials on this site are quoted by type and specification, without a house brand on the wire. We can quote woven field fence, hog and horse wire, barbed and barbless wire, high-tensile wire, T-posts, treated posts, H-brace components, livestock panels, corral boards, farm gates, and typical electric-fence accessories. We do not design or certify electric-fence systems.

Distance and rolls

Field fence is often counted at 330 feet per roll, a common agricultural roll length. At that length, a quarter mile — 1,320 feet — is about four rolls, a half mile is about eight, and a mile is about 16. Confirm the roll you actually want, because a different roll length changes the count, and leftover on a short run is normal. Do not cut the last roll out of the list just because the arithmetic came out neat.

Barbed or barbless wire is often counted at 1,320 feet per reel, a common 80-rod reel. One strand on a quarter-mile line is about one reel; a mile of one strand is about four. Multiply by the number of strands, and say whether the strands sit above a woven run or stand alone. High-tensile work uses its own end assemblies and should be quoted from a design or a careful takeoff, not from a roll count only.

Posts per quarter mile

On a single straight run with no gates or corners, total posts equal the number of spaces plus one, counting both ends. At eight-foot spacing, 1,320 feet is 166 posts, of which 164 are line posts. At ten feet, 133 total. At twelve feet, 111 total. At sixteen feet, about 84 total, because 1,320 does not divide evenly by 16 and the last space is rounded up. Twelve feet is a common planning spacing on woven field fence; tighten it in low spots, at high livestock pressure, or where a specification requires it.

Those figures do not include corners or gates. Every corner and every opening needs posts and, on a tensioned woven or stranded run, H-brace assemblies. A straight quarter mile with one 12-foot gate is a different list from a square paddock of the same perimeter. The farm product page has a chart for the straight-run math. For a planning count on a quarter mile of woven wire, use the material takeoff and edit the footage and gate count.

T-posts, wood posts, and braces

T-posts are a common line post on woven field fence and are typically driven, not set in concrete. Treated round or sawn wood posts are typically used at ends, corners, and gates, and they can be used as line posts when the specification calls for them. If end posts are set in concrete, the bag count belongs on those posts only, not on every T-post. The material takeoff follows that pattern and counts concrete on those end posts only.

H-braces are not decorative. A run pulled tight on weak ends will lean. Plan braces at ends, corners, and gate openings, and say if an existing fence or a building is supposed to serve as an end, because that is often an optimistic assumption. Stays, clips, and wire ties follow the post count and the wire type; they should appear on a real takeoff even if a list does not itemize every clip.

Gates, livestock, and when to send a plan

A 12-foot farm gate is a common planning width. Measure the equipment that has to pass. A wider leaf, a double opening, or a gate on a slope will change the hinge post and the hardware. Hog wire, horse wire, and cattle panels are specified by the animal and the mesh or the panel height, not by swapping a roll of field fence and hoping. Panels and corral boards are usually the right conversation for pens and alleys, not for a mile of boundary fence.

Stop using a straight-run count when the property has a lot of corners, creeks, cuts and fills, or mixed wire types, or when a high-tensile design is involved. Send a sketch or a plat, mark the gates, and ask for a takeoff. For a simple straight line, start with the chart or the material takeoff, edit the footage and gate count, and send the result for a quote. Request a quote for current pricing. The arithmetic will get you close; the site will still decide the last post.

Pickup is at the Gallatin yard Monday through Friday, 7:00 a.m. to 3:00 p.m., and we deliver to job sites in the states we serve. If the run is long enough that you are thinking in miles rather than in backyard feet, put the distance in miles or in feet on the request, not only in “a few rolls,” so we price the same job you are walking.

All resources