
Resources
Fence glossary
Common terms used when specifying and quoting fence materials.
A
- Above-grade height
- The height of the fence from finished grade to the top of the pickets, fabric, or rail. Post length must also cover embedment below grade.
- Aluminized fabric
- Chain-link fabric coated with aluminum rather than zinc. It is one of the metallic coatings commonly quoted alongside galvanized fabric.
- Authority having jurisdiction (AHJ)
- The local building department or code official who sets requirements such as frost depth, pool-barrier rules, and permit conditions for a job site.
B
- Back rail
- A rail on the inside face of a wood fence, or a second rail used to stiffen a gate or a tall run.
- Barbed wire
- Steel wire with barbs at intervals, used on agricultural boundaries and sometimes on the top of commercial chain-link terminals. Strand count and gauge are specified on the quote.
- Board-on-board
- A wood privacy pattern in which boards on one face overlap the joints of boards on the opposite face, so the fence does not show open seams when viewed on an angle.
- Bottom-locking slats
- Privacy slats designed to lock at the bottom of the chain-link mesh so they are harder to lift out than simple drop-in slats.
- Brace band
- A fitted band used on a chain-link terminal post to hold a brace rail or other framework member.
C
- Cane bolt
- A vertical rod, usually mounted on a gate leaf, that drops into a hole in the drive or a receiver to hold the leaf in place. Often used on the inactive leaf of a double-drive gate.
- Cantilever gate
- A sliding gate that is supported from the fence line and counterbalanced so it can open across a driveway without a track across the opening.
- Cap rail
- A horizontal board or rail that sits on top of a wood or vinyl privacy fence to finish the top and protect the picket ends.
- Class I / Class II zinc coating
- Common designations for the weight of zinc on galvanized chain-link fabric. Class II is a heavier coating than Class I and is often specified on more demanding jobs.
- Commercial framework
- Heavier chain-link pipe or tube, often specified with larger outside diameters and SS40 wall thickness, used on commercial and industrial runs.
- Corner post
- A terminal post at a change of direction. It is usually larger than a line post and is often braced.
D
- Dog-ear picket
- A wood picket with the two top corners cut off, leaving a short flat at the top. It is one of the most common residential wood-picket profiles.
- Drop rod
- A rod used to pin a gate leaf to the ground or to a receiver, similar in purpose to a cane bolt.
E
- End post
- A terminal post at the start or end of a run, usually larger than a line post and often braced.
- Extruded vinyl-coated fabric
- Chain-link fabric in which the colored coating is extruded over the metallic wire. Finish gauge is the size after coating and is a common way residential coated fabric is described.
F
- Field fence
- Woven-wire agricultural fence with horizontal lines and vertical stays, used for livestock and property lines. Height, gauge, and stay spacing vary by specification.
- Flat-top panel
- An ornamental aluminum (or similar) panel whose pickets end in a flat or slightly rounded top rather than a spear.
- Framework
- The posts, top rail, and related pipe or tube that support chain-link fabric.
- French gothic picket
- A wood picket with a decorative pointed or sculpted top, more formal than a plain dog-ear.
- Frost depth
- The design depth of frost penetration used by the local building department to set how deep a footing or post should go. It varies by jurisdiction and must be confirmed locally.
- Fused-bonded coating
- A chain-link coating method in which the color coat is bonded to the metallic wire. It is often specified where a tougher coated finish is wanted.
G
- Galvanized after weave (GAW)
- Chain-link fabric that is woven first and then galvanized, so the zinc also covers the cut ends at each knuckle.
- Galvanized before weave (GBW)
- Chain-link fabric woven from wire that was already galvanized. Cut ends at the knuckles are not coated after weaving.
- Gate frame
- The structural frame of a gate, which may be wood, welded steel tube or pipe, or an internal aluminum frame inside a vinyl gate.
- Gothic picket
- A wood picket with a simple pointed top.
- Ground-contact treatment
- A pressure-treated lumber rating meant for wood that will touch the ground or be embedded in soil or concrete. Fence posts set in the ground are commonly specified this way.
H
- H-brace
- A braced assembly, usually two posts and a horizontal member with a diagonal wire or rod, used at ends, corners, and gates on woven-wire and high-tensile fence.
- High-tensile wire
- Steel fence wire made to be tensioned to a high pull. It is used on agricultural boundary and livestock fence, sometimes electrified.
K
- Kickboard / rot board
- A horizontal board at the bottom of some wood fences, used as a sacrificial or closing board against grade. Not every privacy specification uses one.
- Knuckle
- The bent end of a chain-link wire where it locks to the adjacent picket in the weave. Tops and bottoms may be knuckled or twisted, depending on the specification.
L
- Line post
- An intermediate post in a run, smaller than the terminal posts, that supports the rails, panels, or fabric between ends, corners, and gates.
- Loop cap
- A chain-link cap that lets the top rail run through the top of a line post.
M
- Magnetic latch
- A gate latch that uses a magnet to capture the strike, often specified with a top-pull release on pool barriers.
- Mesh size
- The opening size of chain-link fabric, measured between the wires. Two-inch mesh is common on residential and many commercial fences; smaller meshes are used for security, tennis, or privacy weaves.
N
- New England cap
- A pyramidal or house-shaped vinyl post cap, as opposed to a flat cap.
- Nominal size
- The named size of lumber, such as 1x6 or 4x4, which is larger than the actual dressed dimensions. Takeoffs should be clear about nominal versus actual width when counting pickets.
O
- Outside diameter (OD)
- The outside measurement of chain-link pipe or tube, used to size posts, rails, and fittings. Common sizes we quote range from 1-3/8 in. to 4 in.
P
- Panel (ornamental or vinyl)
- A factory or kit section of fence that installs between posts, as opposed to stick-built pickets and rails assembled on site.
- Picket
- A vertical board or extrusion in a wood, vinyl, or ornamental fence. Width, profile, and spacing define the style.
- Pool-code spacing
- Picket or fabric spacing and gate hardware laid out to meet common swimming-pool barrier rules. Local code must be confirmed; a supplier's 'pool-style' panel is not a code certification.
- Post cap
- A cap that finishes the top of a post, used on wood, vinyl, aluminum, and chain-link posts in different profiles.
- Post spacing
- The on-center distance between posts. Common spacings we quote include 6 or 8 feet on many wood and vinyl styles, about 6 feet on many aluminum panels, and 8 to 10 feet on many chain-link runs.
- Pressure-treated lumber
- Wood treated with preservatives under pressure so it resists decay and insects better than untreated lumber. Retention and incising, not just the words 'treated,' should be confirmed for posts in contact with the ground.
- Privacy section
- A fence section with little or no gap between pickets, commonly tongue-and-groove vinyl or tightly spaced wood boards.
- Puppy picket
- An ornamental aluminum (or similar) layout with a tighter picket spacing on the lower part of the panel, used to reduce the gap near grade.
R
- Rackable panel or gate
- A panel or gate that can follow a slope by racking out of square, instead of being stepped. Not every ornamental style is rackable.
- Rail stiffener
- An aluminum or steel insert used inside a vinyl rail, especially the bottom rail, to resist sag between posts.
- Residential framework
- Lighter chain-link pipe or tube, often specified with smaller outside diameters and SS20 wall thickness, used on many residential runs.
- Retention (PCF)
- The amount of preservative retained in pressure-treated wood, expressed in pounds per cubic foot. Ground-contact southern yellow pine fence posts are commonly quoted at retentions such as 0.40 or 0.60 PCF, depending on the specification and the preservative system.
- Roll gate
- A gate that rolls on a track or wheels across an opening, as opposed to a cantilever gate that is supported only from the fence line.
- Routed post
- A vinyl (or sometimes wood) post with pockets cut for the rails. Vinyl posts on this yard can be routed in-house so rail heights match the section.
S
- Self-closing hinge
- A hinge that returns the gate leaf to the closed position, often specified on pool and pedestrian gates. Spring tension and cycle rating should match the leaf.
- Semi-privacy
- A fence style with small, regular gaps between pickets, offering a partial screen rather than a solid face.
- Shadowbox
- A wood fence with pickets alternated on each side of the rail, so both faces have a finished look and light can pass through the offset joints.
- Slide gate
- A general term for a gate that opens by moving sideways, including track-mounted roll gates and cantilever gates.
- Southern yellow pine (SYP)
- A group of dense southern pines widely used for pressure-treated fence posts, rails, and pickets.
- Spear top
- An ornamental picket that ends in a spear or point rather than a flat top.
- SS20 / SS40
- Common wall-thickness grades for chain-link pipe. SS40 is heavier than SS20 and is often specified on commercial framework and on terminal or gate posts.
- Stay
- A vertical wire or spacer in woven field fence that holds the horizontal line wires apart.
- Steel post (for wood fence)
- A steel post used in place of, or inside, a wood post on a wood fence, often to reduce rot at grade or to hide the structure.
T
- T-post
- A rolled steel fence post with a T-shaped cross section, used on agricultural wire fence, often with clips and a studded face.
- Takeoff
- A material takeoff taken from a plan, a sketch, or a site measure, used to quote posts, rails or panels, fabric or pickets, gates, and hardware.
- Tension band
- A fitted band that holds chain-link fabric to a terminal post with a tension bar.
- Tension bar
- A flat bar woven into the end of chain-link fabric and clamped to the terminal post with tension bands.
- Tension wire
- A taut wire run along the bottom, and sometimes the top, of a chain-link fence to keep the fabric from lifting or rolling.
- Terminal post
- An end, corner, or gate post. It is usually larger than a line post and is the post that fabric or rails terminate against.
- Tongue-and-groove (T&G)
- A picket or board profile that locks to the next one, used on many vinyl privacy sections and on some wood patterns.
- Top rail
- The horizontal rail at the top of a chain-link or ornamental run, or the top rail in a wood or vinyl section.
- Top-pull latch
- A latch released from the top of the gate or a shield, commonly used on pool barriers so it is harder for a small child to operate.
- Treatment retention
- See Retention (PCF). The preservative loading in treated lumber; ground-contact and interior ratings are not interchangeable.
W
- Walk gate
- A pedestrian gate, typically narrower than a vehicle or double-drive opening.
- Windscreen
- A knitted or woven screen attached to chain-link fabric for privacy or wind reduction. It is not a substitute for structural fabric or for slats unless the quote says so.
- Woven wire
- Agricultural fence woven from horizontal and vertical wires, including field fence, goat or sheep fence, and some horse-fence patterns.
Z
- Zinc coating weight
- The amount of zinc on galvanized fabric or framework, often given in ounces per square foot (for example 1.2 oz or 2.0 oz) or by class. Heavier coatings are often specified for longer service in wet or coastal exposures.